Summary:
This will show you how to unpack and setup your new ChromeFX™ Application Machine.
Using the ChromeFX™ Machine to apply the ChromeFX™ System Intermediate coat is detailed in the ChromeFX™ Intermediate Coat Technical Data Sheet

Kit Machine Inventory:
If you ordered a ChromeFX™ Kit, you should have received a combined shipment of product and a large box (approximately 3’x3’x 5’) containing the ChromeFX™ Machine. If you only ordered a machine, you will have received only the box.

In the box, you will find everything you need to set up the ChromeFX™ Machine. If a part from the inventory below is missing, check and see if it was shipped separately.

Item	Quantity
Machine with 4 Pressure Canisters	1
Air Gun	1
Single Component Spray Gun(s)	2
Double Component Spray Gun	1
Air Lines ­ Long	1
Air line ­ Short	1

Machine Connections:
All products needed for the intermediate coat are carried in the pressure canisters. The only outside connection is for an airline that is attached to the side of the front panel. Hoses used for internal connections are color coded as follows:

Contains	Hose Color
Activator	Green
4A	Blue
5B	Yellow
Distilled Water	Clear
Air	Black

Machine Assembly:
You will need a large (15’x15’) area with a 90 lb air pressure supply for assembly and testing. Most connections are tightened only finger tight.

1. Unpack the machine and make sure the pressure canisters are properly seated in the frame.
2. Untangle all hoses and lay out straight. Do not cut ties unless told.
3. Attached to the machine will be 3 sets of hoses that go to guns.
   1. Activator Gun Hoses -One Green Activator line and one Black Air hose
   2. Distilled Water Gun Hoses ­ One Clear Distilled Water hose and One Black Air hose.
   3. 4A/5B 2 component Gun Hoses ­ One Blue 4A hose, one Yellow 5B hose and one Black Air hose.
4. Check and make sure that each colored hose is firmly attached to the correct canister.
5. Check and make sure that air hoses are firmly attached to the air connections.
6. Each canister should have a black air hose attached to an air connection on the machine.
   -Make sure these connections are tight.
7. Assemble the Activator Gun using one of the single component guns as follows:
   1. Trim the Black hose so it is 3” shorter than the Green colored hose.
   2. Insert Black Air hose in base of gun and tighten connection.
   3. Insert Green colored hose in front connection and tighten.
8. Assemble the Distilled Water Gun using the last single component guns as follows:
   1. Trim the Black hose so it is 3” shorter than the clear hose.
   2. Insert Black Air hose in base of gun and tighten connection.
   3. Insert Clear hose in front connection and tighten.
9. Assemble the 4A/5B Gun using the 2 component gun as follows:
   1. Trim the Blue and Yellow hoses to the same length.
   2. Trim the Black hose so it is 3” shorter than the colored hoses.
   3. Insert Black Air hose in base of gun and tighten connection.
   4. Insert the colored hoses in the 2 front connections and tighten.
10. Assemble the Air Gun as follows:
    1. Trim the ends off of the long Black air hose.
    2. Insert one end in the Air Gun and tighten.
    3. Insert the remaining end into the empty connector on the back of the front panel.
11. Attach air hose to external connector to do system pressure check.
12. Do not over pressurize system. Adjust gauges as follows:
    1. Set front panel pressures as follows:
       -Left Side:
       -Middle: "2B37" 30 psi
       -Right Side: "ARIA" 50 psi
    2. Set other gauges as follows:
       -4A tank 30 psi
       -5B tank 30 psi.
       -Air 50 psi
13. Hand tighten any leaking fittings.
14. Turn off air supply and relieve system pressure.
15. System is now ready to be loaded with product.

* Consult current Materials Safety Data Sheet before use of this product.